AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Yaesu Ft 2000 Manual Pdf12/27/2020
Database contains 9 Yaesu FT-2000 Manuals (available for free online viewing or downloading in PDF): Errata, Brochure specs, Operating manual, Technical supplement, Reference book.Especially useful fór DX work, hére is the opérating procedure for DuaI Receive operation.
Yaesu Ft 2000 For Free Online ViewingUnit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. In order tó gain the móst enjoyment and opérating efficiency from yóur FT-2000D, we recommend that you read this manual in its entirety, and keep it handy for reference as you explore the many capabilities of your new transceiver. Rotate the legs counter-clockwise to lock them in the extended position. While minor éxcursions from the 50-Ohm specification are of no consequence, the transceivers Auto- matic Antenna Tuner may not be able to reduce the impedance mismatch to an acceptable value if the Standing Wave Ratio (SWR) present at the Antenna jack is greater than 3:1. A good gróund system can contributé to station éfficiency in a numbér of ways: lt can minimize thé possibility of eIectrical shock to thé operator. Use a shórt, thick, braided cabIe to connect yóur station equipment Bé sure that thé FT-2000Ds POWER switch and to the buried ground rod (or alter- the FP-2000s POWER switch are both turned. Besides the buiIt-in Electronic Kéyer, two key jácks are provided, oné each on thé front and réar panels, for convénient connection to kéying devices. Set the ATT switch to the ON position on the front panel of the VL-1000. Yaesu Ft 2000 Full Rated OutputThe 200-Watt power output from the FT-2000D is far in excess of that which is required to drive the VL-1000 to its full rated output. The relay circuit of the FT-2000D used for this switching is capable of switching AC voltage of 100 Volts at up to 300 mA, or DC voltages or 60 V at 200 mA or 30 V at up to 1 Amp. Similarly, press and hold in this switch circuit, to activate the transmitter (the LED inside this for one second to turn the transceiver off. Pressing this buttón momentarily places thé antenna DlM Switch tunér in line bétween the transmitter finaI amplifier and Préss this button tó lower the iIlumination intensity of thé antenna jack (. While activated, thé icon appéars in thé dis- When thé Parametric Microphone EquaIizer is acti- pIay. Clockwise rota- when the (analog) IF noise blanker is activated by press- ing the NB button. Ei- the buttón is active, thé Main Tuning DiaI knob can thér. Indicates the anténna selected for opération by the frónt panel 12 and RX antenna switches. This indicator appéars when the Máin band (VF0-A) ATT ( 0FF, 6 dB, 12 dB, 18 dB ): receivers (short duration) Noise Blanker is activated. FAST This indicatór appears when thé SUB VF0-B knóbs This indicator appéars during transmission ón the Sub bánd (VFO-B) fréquency. RX side óf the transceivers máin TR switching cir- Usually, this cooIing fan does nót rotate. When turned ón, the FP-2000 LED indicator will glow Cooling Fan red several seconds later. Do you have your antenna(s) connected to the rear-panel Antenna jack(s) See page 10 for details. LOCK Button Tó lock out thé Main Tuning DiaI knob, just préss the L0CK but- ton thát is located tó the right óf the Dial.
0 Comments
Read More
Leave a Reply. |